Manual para ZRD 27 JC (CT 280)

Manual para ZRD 27 JC (CT 280)

Marca: ZANUSSI

Categoría: Refrigerator

Tipo de Documento: Manual

Idioma: ES

Idiomas Disponibles: EN , ES

Subido: 21 de noviembre de 2025 a las 20:42

Información de Garantía

The appliance is guaranteed within the context of and in adherence with the terms laid out in this declaration.

How to use the freezer

Freezing

Freeze fresh and faultless food only. Set the thermostatic control knob to position „3" and put the wire shelf in the frozen food compartment to the highest position. Then put in the quantity to be frozen, directly on the wire shelf. Freezing is completed in approx. 24 hours. After 24 hours set the thermostatic control knob back to „Medium" (2-3) position, or leave that in position „3" which is usually adequate for everyday use.

Storing in the freezer

After finishing freezing it is practical to put the frozen food from the wire shelf in the frozen food compartment to the place under that making room for a next possible freezing. Food already stored is not damaged by another freezing.

How to make ice cubes

To make ice cubes fill the enclosed ice cube tray with water and put it to the frozen food compartment. Setting thermostatic control knob to maximum position can shorten preparing time.

Hints and ideas

This chapter practical hints and ideas are given about how to use the appliance to reach maximum energy saving and there is environmental information about the appliance as well.

How to save energy

  • The colder the ambient temperature of the appliance is the less energy it uses.
  • Avoid putting the appliance in a sunny place and near anything that gives off heat.
  • Be sure that the condenser and the compressor are well ventilated.
  • Wrap products in tightly closing dishes or cling film to avoid building up unnecessary frost.
  • Do not leave the door open longer than necessary and avoid unnecessary openings.

Solución de problemas y códigos de error

Problem Possible cause Solution
It is too warm in the refrigerator. Thermostatic control can be set wrongly. If products are not cold enough or placed wrongly. The door does not close tightly or it is not shut properly. Set the thermostat knob to higher position. Place the products to the appropriate place. Check if the door closes well and the gasket is unhurt and clean.
It is too warm in the freezer. Thermostatic control can be set wrongly. The door does not close tightly or it is not shut properly. Products in big quantity to be frozen were put in. Products to be frozen are placed too closely to each other. Set the thermostat knob to higher position. Check if the door closes well and the gasket is unhurt and clean. Wait some hours and then check the temperature again. Place the products in a way so that cold air could circulate among them.
Water flows at the back plate of the refrigerator. Water flows into the chamber. The outlet of the chamber can be clogged up. Products placed in can prevent water from flowing into the collector. Clean the outlet. Replace the products so that they can not touch the back plate directly. Put the melting water outlet to the evaporative tray.
Water flows onto the floor. The melting water outlet flows not into the evaporative tray above the compressor. Wrap the products better.
There are too much frost and ice. Products are not wrapped properly. Doors are not shut properly or do not close tightly. The thermostatic control can be set wrongly. Check if the doors close well and the gaskets are unhurt and clean. Set the thermostat knob to a position that gives higher temperature.
The compressor operates continually. The thermostatic control is set wrongly. Doors are not shut properly or do not close tightly. Products in big quantity to be frozen were put in. Too warm food was put in. The appliance is in too warm place. Set the thermostat knob to a position that gives higher temperature. Check if the doors close well and the gaskets are unhurt and clean. Wait some hours and then check the temperature again. Put food at max. room temperature. Try to reduce the temperature in the room where the appliance stands.
The appliance does not work at all. Neither cooling, nor lighting works. Indicator lamps do not give light. Plug is not connected to the mains socket properly. The fuse burnt out. The thermostatic control is not on. There is no voltage in the mains socket. (Try to connect another appliance into it.) Connect the mains plug properly. Change the fuse. Start the appliance according to instructions in chapter „Putting it into use". Call an electrician.
The appliance is noisy. The appliance is not supported properly. Check if the appliance stands stable (all the four feet should be on the floor).
Política de Privacidad