Marca: SHARP
Categoría: Audio
Tipo de Documento: Piezas/Servicio
Idioma: ES
Idiomas Disponibles: EN , ES
Piezas/Servicio para CD-BK260V/CD-BK2700V/CD-BK280V
Subido: 21 de noviembre de 2025 a las 19:02
Fecha de Publicación del Manual: 2001-01-01
Información de Garantía
Copyright 2001 by SHARP CORPORATION. All rights reserved. Reproduction of this publication is prohibited.
Setting the Clock
- Press ON/STAND-BY to turn on the unit.
- Press CLOCK and then MEMORY/SET within 5 seconds.
- Press TUNING/TIME to select 24-hour or 12-hour display, then press MEMORY/SET.
- Press TUNING/TIME to set the hour, then press MEMORY/SET.
- Press TUNING/TIME to set the minutes, then press MEMORY/SET.
Setting the AC voltage selector
Check the AC voltage selector on the rear panel. Adjust with a screwdriver to match your local voltage (110 V, 127 V, 220 V, or 230 V-240 V AC).
Connecting the AC power lead
Connect the AC power lead after all other connections are made. Unplug for prolonged periods of non-use. Use AC plug adaptor if required for your wall socket.
Setting the FM/AM span selector
Set the SPAN SELECTOR switch on the rear panel according to your region's FM/AM frequency intervals (50/9 kHz or 100/10 kHz).
Solución de problemas y códigos de error
| Symptom | Possible Cause |
|---|---|
| General | |
| The clock is not on time. | Did a power failure occur? Reset the clock. |
| When a button is pressed, the unit does not respond. | Set this unit to the power stand-by mode and then turn it back on. If malfunction persists, reset it. |
| No sound is heard. | Is the volume level set to "0"? Are the headphones connected? Are the speaker wires disconnected? Is the karaoke mode set to "L-CH", "R-CH" or "V-CANCEL"? |
| Video CD | |
| The picture is not displayed during playback. | Is the TV unplugged? Is the unit connected improperly? Is the input selector on the TV set to other than "VCR"? Is the unit being played without selecting video CD? |
| The picture quality is poor, or it is distorted. | Is the disc very dirty? |
| CD player | |
| Playback does not start. | Is the disc loaded upside down? |
| Playback stops in the middle or is not performed properly. | Does the disc satisfy the standards? Is the disc distorted or scratched? Is the unit located near excessive vibrations? Is the disc very dirty? Has condensation formed inside the unit? |
| Tuner | |
| Radio makes unusual noise consecutively. | Is the unit placed near the TV or computer? Is the FM aerial or AM loop aerial placed properly? Move the AC power lead away from the aerial if located near. |
| Cassette deck | |
| Cannot record. | Is the erase-prevention tab removed? |
| Cannot record tracks with proper sound quality. | Is it a normal tape? (You cannot record on a metal or CrO2 tape.) |
| Cannot erase completely. | Is there any slack? Is the tape stretched? |
| Sound skipping. | Are the capstans, pinch rollers, or heads dirty? |
| Cannot hear treble. | If a power failure occurs during playback, the heads remain engaged with the tape. |
| Sound fluctuation. | Do not open the compartment forcibly. Wait until electricity resumes. |
| Cannot remove the tape. | - |
| Karaoke | |
| The vocal part of a multiplexed disc is not heard. | Is the karaoke mode set to "L-CH", "R-CH" or "V-CANCEL"? |
| Remote control | |
| The remote control does not operate. | Is the AC power lead of the unit plugged in? Is the battery polarity respected? Are the batteries dead? Is the distance or angle incorrect? Does the remote control sensor receive strong light? |